15 min
Why the OPEN sign needs a resistor
Your friend wants a glowing OPEN sign for their sneaker stall, running from a USB power bank. Wire an LED straight to it and it dies. One part the size of a grain of rice saves it.
Ticket 01 · The guess
How much push does the LED want?
Words to know
Sources and every number (10)
Sources
- Universal Serial Bus Type-C Cable and Connector Specification, Release 2.0 (Table 4-17, Precedence of power source usage: default USB power is 5 V) · USB Implementers Forum, 2019
- WP7113ID T-1 3/4 (5mm) Solid State Lamp data sheet (Rev V.14A): forward voltage, test current and absolute maximum DC forward current · Kingbright, 2026
- WP7113QBC/D T-1 3/4 (5mm) Solid State Lamp data sheet (Rev V.18B): blue LED forward voltage · Kingbright, 2025
- Blink (built-in example): the 220-ohm resistor and a typical red LED's voltage (page renders with JavaScript; text read in Arduino's docs-content source on GitHub) · Arduino, 2026
- Metric (SI) Prefixes (kilo: ten to the third, thousand; mega: ten to the sixth, million) · National Institute of Standards and Technology, 2025
- E-Series Values: standard series values in a decade for resistances and capacitances, according to IEC 60063 (document 28372) · Vishay, 2012
- Electric Vehicles for Consumers (a standard 120 volt household outlet) · Alternative Fuels Data Center, U.S. Department of Energy, 2026
- Controlling Electrical Hazards (OSHA 3075, 2002 revised): effects of electric current in the human body · Occupational Safety and Health Administration, 2002
- Secondary School Students' Misconceptions about Simple Electric Circuits (Journal of Turkish Science Education, vol. 4, no. 1), Hüseyin Küçüközer and Sabri Kocakülah · Journal of Turkish Science Education, 2007
- University Physics Volume 3, 9.7 Semiconductor Devices (a diode lets current flow in only one direction, like a one-way valve) · OpenStax, Rice University, 2016
Every number
- 5 V
usb.org ·2019 · USB's standard (default) push. - 1.9 V
kingbrightusa.com ·2026 · Typical forward voltage of a red LED (Kingbright's data sheet) at ten milliamps. - 10 mA
kingbrightusa.com ·2026 · The current the maker measures this LED at. - 30 mA
kingbrightusa.com ·2026 · The most steady current the maker allows. - 3.3 V
kingbrightusa.com ·2025 · Typical forward voltage of a blue LED (Kingbright's data sheet). - 220 Ω
arduino.cc ·2026 · The resistor Arduino's first LED tutorial uses with its five-volt board. - 1.8–
2.2 V arduino.cc ·2026 · The range Arduino's guide gives for a typical red LED's voltage. - 3.1 V
(example number: Worked out: the supply's push minus the red LED's forward voltage.) · Worked out: the supply's push minus the red LED's forward voltage. - 14.1 mA
(example number: Worked out: the leftover volts divided by the Arduino tutorial's resistor.) · Worked out: the leftover volts divided by the Arduino tutorial's resistor. - 1,000 mA
nist.gov ·2025 · Milli means a thousandth (NIST's table of SI prefixes), so this many milliamps make one amp. - 0.0141 A
(example number: Worked out: the leftover volts divided by the Arduino tutorial's resistor, in amps.) · Worked out: the leftover volts divided by the Arduino tutorial's resistor, in amps. - 20 mA
(example number: Simplified example: a brighter target, still under the maker's limit.) · Simplified example: a brighter target, still under the maker's limit. - 0.02 A
(example number: Worked out: the brighter target turned from milliamps into amps.) · Worked out: the brighter target turned from milliamps into amps. - 155 Ω
(example number: Worked out: the leftover volts divided by the brighter target in amps.) · Worked out: the leftover volts divided by the brighter target in amps. - 5 mA
(example number: Simplified example: a dimmer glow for an evening market, still easy to see.) · Simplified example: a dimmer glow for an evening market, still easy to see. - 0.005 A
(example number: Worked out: the dimmer target turned from milliamps into amps.) · Worked out: the dimmer target turned from milliamps into amps. - 620 Ω
(example number: Worked out: the leftover volts divided by the dimmer target in amps.) · Worked out: the leftover volts divided by the dimmer target in amps. - 310 Ω
(example number: Worked out: the leftover volts divided by the wanted current in amps.) · Worked out: the leftover volts divided by the wanted current in amps. - 330 Ω
vishay.com ·2012 · The next standard resistor size above the worked-out value (the standard E series, twelve sizes to a decade). - 9.4 mA
(example number: Worked out: the leftover volts divided by the standard resistor.) · Worked out: the leftover volts divided by the standard resistor. - 33 Ω
(example number: The build sheet's mistake: a zero dropped from the standard size.) · The build sheet's mistake: a zero dropped from the standard size. - 94 mA
(example number: Worked out: the leftover volts divided by the mistyped resistor.) · Worked out: the leftover volts divided by the mistyped resistor. - 9 V
(example number: Simplified example: a nine-volt battery.) · Simplified example: a nine-volt battery. - 3 V
(example number: Worked out: two AA batteries, each about one and a half volts, in a row.) · Worked out: two AA batteries, each about one and a half volts, in a row. - 100 Ω
(example number: Simplified example: a small resistor.) · Simplified example: a small resistor. - 120 V
energy.gov ·2026 · A standard US wall outlet. - 1 mA
osha.gov ·2002 · OSHA's table: the current that gives a faint tingle. - 5 mA
osha.gov ·2002 · OSHA's table: the current that gives a slight shock, not painful but disturbing. - 50–
150 mA osha.gov ·2002 · OSHA's table: the current that brings extreme pain, stopped breathing and possible death.